Flange Facing Services in Dammam
From fabrication yards to plant maintenance, Dammam has a steady demand for flange faces corrected on site. We bring the machines to you.
Correcting flange faces in Dammam
Dammam fabrication shops sometimes find flanges with the wrong finish or weld distortion, and plants in the industrial cities have faces damaged in service. Flange facing in Dammam handles both, machining faces flat and to the specified finish without sending spools out.
After machining we check the finish against a comparator and take flatness readings, so the joint can be rebuilt on a face that will actually seal.
Most flange facing jobs in Dammam are part of a wider joint repair, so the same crew can also handle bolt torquing in Dammam and the other services below. For methods, equipment and standards, see our main flange facing services in KSA page.
Flange Facing jobs we do in Dammam
Work we are regularly asked for at industrial cities, fabrication, port sites in and around Dammam.
Weld distortion correction
Machining flange faces that have pulled out of flat after welding on fabricated spools.
Heat exchanger faces
Channel, shell and floating head faces machined in place, without sending the equipment to a workshop.
Corrosion pitting
Pitted faces cleaned up, with weld build-up and re-machining where the pits are deep.
Our flange facing process in Dammam
Four steps, run under your permit-to-work system and recorded for your files.
Inspect and measure
We record the damage and check how much material can be removed within the flange rating.
Mount and true
The facer is clamped on the ID or OD and set square to the flange axis.
Machine
Light cuts remove the damage and a finishing pass gives the specified profile.
Verify
Finish, flatness and runout are checked and recorded before reassembly.
Getting a flange facing crew to Dammam
Dammam is where much of our equipment is kept, so most jobs here can start within the day.
Machines, tools and consumables are checked against your scope before departure, and the crew arrives with PPE, permits planned and the paperwork your site asks for.
Calibrated equipment
Instruments and tools travel with current calibration certificates, listed in the job record.
Single point of contact
One supervisor coordinates flange facing with bolting and the other joint services on the Dammam job.
Other joint services in Dammam
Every service a bolted joint needs, from the same team.
Bolt Torquing in Dammam
Hydraulic torque wrenches and stud tensioners applying a calculated bolt load, pass by pass, with a tagged record for each joint.
View bolt torquing in DammamPipe Cold Cutting in Dammam
Spark-free clamshell and split-frame cutting and bevelling for live plants where hot work is not allowed.
View pipe cold cutting in DammamNitrogen Purging in Dammam
Inerting, oxygen-free purging, drying and nitrogen leak testing before start-up or after maintenance.
View nitrogen purging in DammamHydrotest in Dammam
Hydrostatic pressure testing of piping, vessels and spools with calibrated pumps, gauges and recorders.
View hydrotest in DammamFlange Facing in Dammam: common questions
Can you machine flanges in our Dammam yard?
Yes. We bring portable facers to the yard and check finish and flatness to your QC requirements.
Do you reassemble the joint after facing in Dammam?
Yes. Our bolting crew can fit the new gasket and tighten the joint to a calculated load, so one team is responsible for the result.
Can flanges be refaced in place in Dammam?
Yes. Our machines clamp to the flange where it is installed, so pipework and equipment stay in place and only the joint is opened.
Flange Facing near Dammam
Our flange facing crews also work in these nearby cities.
Request flange facing in Dammam
Tell us the flanges and where they are in Dammam. We usually respond within the day.
- Phone+966 50 605 8927
- Emailalviqaisar@gmail.com
- BaseEastern Province, Kingdom of Saudi Arabia
- HoursOffice Sunday to Thursday, 7 AM to 5 PM. Field call-outs any day, any hour.