Hydrotest Services in Makkah
New chilled-water and fire-water systems in Makkah buildings must be tested before use. We test them and keep disruption low.
Hydrotesting in Makkah
Hotels, district cooling plants and utilities in Makkah regularly add or modify chilled-water, fire-water and water supply systems. Hydrotest services in Makkah test them before commissioning, planned around the busy seasons and working inside occupied buildings.
We work from your approved test packs: blinds and vents are fitted, the system is filled from the low point and vented at the high points before pressure is raised.
Most hydrotesting jobs in Makkah are part of a wider joint repair, so the same crew can also handle bolt torquing in Makkah and the other services below. For methods, equipment and standards, see our main hydrotest services in KSA page.
Hydrotest jobs we do in Makkah
Work we are regularly asked for at water, district cooling, buildings sites in and around Makkah.
Fire-water system tests
Testing new fire-water systems in hotels and public buildings.
Test pack execution
Running pre-commissioning test packs from blinding through to sign-off and reinstatement.
Vessel and drum tests
Testing pressure equipment after repair or alteration, isolated from connected piping.
Our hydrotesting process in Makkah
Four steps, run under your permit-to-work system and recorded for your files.
Review the test pack
Test boundaries, pressure, hold time and isolations are confirmed.
Prepare and fill
Blinds, vents and drains are fitted and the system is filled and vented.
Pressurise and hold
Pressure is raised in stages, held and recorded while the system is inspected.
Drain and reinstate
The system is drained, dried if needed, and permanent joints are reinstated.
Getting a hydrotesting crew to Makkah
Makkah is served by our Jeddah-based crews, and we plan work around the busy seasons.
Machines, tools and consumables are checked against your scope before departure, and the crew arrives with PPE, permits planned and the paperwork your site asks for.
Calibrated equipment
Instruments and tools travel with current calibration certificates, listed in the job record.
Single point of contact
One supervisor coordinates hydrotesting with bolting and the other joint services on the Makkah job.
Other joint services in Makkah
Every service a bolted joint needs, from the same team.
Bolt Torquing in Makkah
Hydraulic torque wrenches and stud tensioners applying a calculated bolt load, pass by pass, with a tagged record for each joint.
View bolt torquing in MakkahPipe Cold Cutting in Makkah
Spark-free clamshell and split-frame cutting and bevelling for live plants where hot work is not allowed.
View pipe cold cutting in MakkahFlange Facing in Makkah
On-site machining that restores flange sealing faces to the right finish and flatness, without removing the pipe.
View flange facing in MakkahNitrogen Purging in Makkah
Inerting, oxygen-free purging, drying and nitrogen leak testing before start-up or after maintenance.
View nitrogen purging in MakkahHydrotest in Makkah: common questions
Can you hydrotest inside occupied buildings in Makkah?
Yes. We plan filling, testing and draining to keep disruption and water spills to a minimum.
What test pressure do you use for hydrotests in Makkah?
The test pressure comes from the code that governs the system and its design conditions, as set out in your approved test pack.
Do you test stainless steel systems in Makkah?
Yes. We control water quality, particularly chloride content, and drain and dry stainless systems promptly after the test.
Hydrotest near Makkah
Our hydrotesting crews also work in these nearby cities.
Request hydrotesting in Makkah
Send the system and timing in Makkah. We will reply with a plan and price.
- Phone+966 50 605 8927
- Emailalviqaisar@gmail.com
- BaseEastern Province, Kingdom of Saudi Arabia
- HoursOffice Sunday to Thursday, 7 AM to 5 PM. Field call-outs any day, any hour.