Flange Facing Services in Madinah
Factories and utilities in Madinah both run into damaged faces. We machine them on site to stop leaks at the source.
Flange facing across Madinah
The Madinah industrial city and the water and cooling systems serving the city have pump, valve and piping flanges that wear over time. Flange facing in Madinah restores them in place, avoiding the delay of removing equipment.
Light cuts remove pitting, radial scratches and erosion, then a finishing pass produces the serrated, smooth or RTJ profile your joint calls for.
Most flange facing jobs in Madinah are part of a wider joint repair, so the same crew can also handle bolt torquing in Madinah and the other services below. For methods, equipment and standards, see our main flange facing services in KSA page.
Flange Facing jobs we do in Madinah
Work we are regularly asked for at industry, water, district cooling sites in and around Madinah.
Factory process flanges
Machining process and utility flanges in industrial city plants.
RTJ groove re-cutting
Worn ring grooves on high-pressure joints re-machined and gauged before a new ring is fitted.
Construction damage
Flanges dented or scratched during construction corrected before commissioning.
Our flange facing process in Madinah
Four steps, run under your permit-to-work system and recorded for your files.
Inspect and measure
We record the damage and check how much material can be removed within the flange rating.
Mount and true
The facer is clamped on the ID or OD and set square to the flange axis.
Machine
Light cuts remove the damage and a finishing pass gives the specified profile.
Verify
Finish, flatness and runout are checked and recorded before reassembly.
Getting a flange facing crew to Madinah
Madinah is reached from Jeddah or Yanbu, and we often combine it with Yanbu scopes.
Machines, tools and consumables are checked against your scope before departure, and the crew arrives with PPE, permits planned and the paperwork your site asks for.
Calibrated equipment
Instruments and tools travel with current calibration certificates, listed in the job record.
Single point of contact
One supervisor coordinates flange facing with bolting and the other joint services on the Madinah job.
Other joint services in Madinah
Every service a bolted joint needs, from the same team.
Bolt Torquing in Madinah
Hydraulic torque wrenches and stud tensioners applying a calculated bolt load, pass by pass, with a tagged record for each joint.
View bolt torquing in MadinahPipe Cold Cutting in Madinah
Spark-free clamshell and split-frame cutting and bevelling for live plants where hot work is not allowed.
View pipe cold cutting in MadinahNitrogen Purging in Madinah
Inerting, oxygen-free purging, drying and nitrogen leak testing before start-up or after maintenance.
View nitrogen purging in MadinahHydrotest in Madinah
Hydrostatic pressure testing of piping, vessels and spools with calibrated pumps, gauges and recorders.
View hydrotest in MadinahFlange Facing in Madinah: common questions
Do you combine Madinah flange facing with Yanbu work?
Yes. Combining nearby jobs saves travel time and cost.
How much material do you remove from a flange face?
Only enough to clean up the damage, usually a fraction of a millimetre. We measure first and never machine below the thickness the rating allows.
Do you reassemble the joint after facing in Madinah?
Yes. Our bolting crew can fit the new gasket and tighten the joint to a calculated load, so one team is responsible for the result.
Flange Facing near Madinah
Our flange facing crews also work in these nearby cities.
Request flange facing in Madinah
Send the site and flange details in Madinah. We will reply with a plan and price.
- Phone+966 50 605 8927
- Emailalviqaisar@gmail.com
- BaseEastern Province, Kingdom of Saudi Arabia
- HoursOffice Sunday to Thursday, 7 AM to 5 PM. Field call-outs any day, any hour.