Pipe Cold Cutting Services in Al Ahsa
Gas plants and separation facilities around Al Ahsa run high-pressure, thick-wall pipe. Our machines cut and bevel it without heat.
Heavy-wall cold cutting in Al Ahsa
The Al Ahsa area is full of gas processing and separation plants linked by flowlines and trunk lines. Pipe cold cutting in Al Ahsa is used for heavy-wall pipe in these systems, where a clean machined bevel shortens welding time and a heat-free cut avoids changing the metallurgy next to the weld.
Each cut is made by a parting tool and a bevel tool turning together on a frame centred on the pipe, which gives a square, machined end ready for fit-up.
Most pipe cold cutting jobs in Al Ahsa are part of a wider joint repair, so the same crew can also handle bolt torquing in Al Ahsa and the other services below. For methods, equipment and standards, see our main pipe cold cutting services in KSA page.
Pipe Cold Cutting jobs we do in Al Ahsa
Work we are regularly asked for at gas plants, gosps, oilfield sites in and around Al Ahsa.
GOSP piping modifications
Cutting heavy-wall separator and header piping for new connections at gas-oil separation plants.
Tie-in cuts on live units
Opening existing lines for new branches while the rest of the plant keeps running.
Pipeline section changes
Removing damaged pipeline sections and preparing ends for new pipe or fittings.
Our pipe cold cutting process in Al Ahsa
Four steps, run under your permit-to-work system and recorded for your files.
Review and isolate
We confirm line size, schedule and content, and your team isolates and clears it under permit.
Support and mount
The pipe is supported either side and the split frame is clamped and centred.
Cut and bevel
Parting and bevel tools feed in together at low speed until the wall is through.
Check and hand over
Bevel angle, land and squareness are checked before the end is handed to your welders.
Getting a pipe cold cutting crew to Al Ahsa
Al Ahsa is around two hours by road. For shutdowns we can base the crew in Hofuf, close to the plants.
Machines, tools and consumables are checked against your scope before departure, and the crew arrives with PPE, permits planned and the paperwork your site asks for.
Calibrated equipment
Instruments and tools travel with current calibration certificates, listed in the job record.
Single point of contact
One supervisor coordinates pipe cold cutting with bolting and the other joint services on the Al Ahsa job.
Other joint services in Al Ahsa
Every service a bolted joint needs, from the same team.
Bolt Torquing in Al Ahsa
Hydraulic torque wrenches and stud tensioners applying a calculated bolt load, pass by pass, with a tagged record for each joint.
View bolt torquing in Al AhsaFlange Facing in Al Ahsa
On-site machining that restores flange sealing faces to the right finish and flatness, without removing the pipe.
View flange facing in Al AhsaNitrogen Purging in Al Ahsa
Inerting, oxygen-free purging, drying and nitrogen leak testing before start-up or after maintenance.
View nitrogen purging in Al AhsaHydrotest in Al Ahsa
Hydrostatic pressure testing of piping, vessels and spools with calibrated pumps, gauges and recorders.
View hydrotest in Al AhsaPipe Cold Cutting in Al Ahsa: common questions
Can you cold cut heavy-wall pipe in Al Ahsa?
Yes. We use hydraulic drives and tooling suited to heavy walls, cutting and bevelling in one set-up.
Can you cut and bevel in one set-up in Al Ahsa?
Yes. The parting tool and bevel tool run on the same frame, so the pipe is cut and bevelled in one set-up, including compound bevels and J-preps.
What pipe sizes can you cold cut in Al Ahsa?
Our split-frame machines cover small-bore lines up to large-diameter pipe. Send the outside diameter, schedule and material and we will confirm the machine.
Pipe Cold Cutting near Al Ahsa
Our pipe cold cutting crews also work in these nearby cities.
Request pipe cold cutting in Al Ahsa
Send the plant, pipe schedule and dates in Al Ahsa. We will reply with machines and a price.
- Phone+966 50 605 8927
- Emailalviqaisar@gmail.com
- BaseEastern Province, Kingdom of Saudi Arabia
- HoursOffice Sunday to Thursday, 7 AM to 5 PM. Field call-outs any day, any hour.